How To Replace A Bathtub (For Newbies).
Schedule EstimateIn this article in the next paragraph you will discover a bunch of good quality news pertaining to How to Install a Bathtub.
Setting up a tub isn't specifically brain surgery, yet it does call for solid plumbing, carpentry, and in some cases, tiling abilities. Changing an old tub with a brand-new one is also a moderately difficult project. If the old bathtub is readily accessible, the project can move quickly; if you need to open up a wall to eliminate the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly need a helper to leave the old bathtub and set in the new one. Make sure you have actually certified on your own for the work and also fit trying it. Instead of employing a professional to take over a halfway-completed job, it is much better to consider employing one before you start. Possibilities are you may need a professional plumber to make tube links.
This post will help you mount a brand-new tub in your shower room if you have already purchased a new bathtub and also don't need to transform the plan of your previous supply of water pipes.
Your devices and also material checklist should consist of the following:
Planning for the Installation
Firstly, the sustaining frame provided with the bath needs to be fitted (if called for) according to the producer's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is essential to see to it that if the tap comes with a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the faucets system to prevent stress on the bathtub.
Fit the flexible faucet ports to the bottom of the two faucets making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you use every one of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom must now prepare to be fitted in its final placement.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your setup, then the first thing you must do is disconnect the water supply. After doing so, activate the taps to drain pipes any type of water remaining in the system. The procedure of removing the existing faucets can be quite bothersome because of the restricted gain access to that is frequently the instance.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the taps. Have a towel ready for the continuing to be water that will originate from the pipes. As soon as the supply pipes have actually been removed, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from turning throughout this process. As soon as the taps have actually been removed, the holes in the bath/basin will need to be cleaned of any kind of old sealing substance.
Prior to proceeding to fit the brand-new taps, compare the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Mounting the Bathtub
Utilizing both wood boards under its feet, position the bathtub in the needed setting. The wood boards are valuable in evenly spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto 4 small points.
The next goal is to make sure that the bath tub is leveled all round. This can be attained by checking the spirit level and changing the feet on the tub up until the level reviews degree.
To mount faucets, fit all-time low of the furthest adaptable tap port to the proper supply pipe by making a compression sign up with; after that do the exact same for the various other faucet.
Switch on the water supply as well as inspect all joints and also brand-new pipework for leakages and also tighten them if essential. Load the bathtub as well as additionally examine the overflow outlet as well as the typical electrical outlet for leakages.
Lastly, repair the bath paneling as explained in the producer's instruction manual. Tiling and sealing around the bathtub should wait until the bath tub has actually been made use of at the very least when as this will certainly settle it into its final position.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic adapter to stop damages to the thread. One end of the connector fits on the plastic tail of the tap and the various other end gives a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly need decreasing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, position the tap in the mounting opening in the bath/basin making sure that the washers are in area in between the tap and the sink. Safeguard the faucet in place with the manufacturer given backnut. When the tap is firmly in position, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical tap adapters. The former kind ought to be connected to the faucet ends initially, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the area where the bathroom fulfills the ceramic tile, it is necessary to seal the accompanies a silicone rubber caulking. This is essential as the installation can move enough to fracture a rigid seal, triggering the water to pass through the wall in between the bath as well as the tiling, bring about problems with wetness and feasible leakages to the ceiling below.
You can pick from a variety of coloured sealers to blend in your components and fittings. They are offered in tubes and also cartridges, and can securing gaps approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always fill up the bath tub with water before securing, to allow for the motion experienced when the tub is in use. The sealer can crack relatively very early if you do not take into account this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise quickly readily available on the market. It is recommended to fit the floor tiles using water-resistant or waterproof sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you liked our piece about A Step-by-Step Guide to Installing a Bathtub. Thanks a ton for taking a few minutes to read through our blog post. Loved our blog? Please share it. Help someone else find it. Thanks so much for going through it.
Click On This Link